support@canvastentshop.ca
1-800-234-1150
We accept orders
Monday - Saturday
7am - 5:30pm
Pacific Time

Wall Tent Shop Accepts PayPal
We accept Paypal payments. Please call.

Canvas Tent Shop Blog

Contact us by Email
support@canvastentshop.ca

Canvas Tent Shop
Castelgar, BC, Canada
1-800-234-1150

TENT FRAME ANGLE JOINT KITS

WILDERNESS 120º ANGLE JOINTS ARE IN STOCK AND CAN SHIP IN 1 - 3 BUSINESS DAYS.

 

*****************NEW HOURS: MONDAY-SATURDAY 7:30 AM TO 5:30 PACIFIC TIME**************************

ANGLE KITS FOR NEW FRAME


ANGLE KIT - CONDUIT CUT LIST FOR A NEW TENT

MOST 12', 14', 15', 16' & 18' WIDE TENTS REQUIRE THE 120º ANGLE JOINTS.

Angle KIT / Joint Diagram - shown as a three rafter angle kit
Each kit contains 9 angles.


POLES NOT INCLUDED

4 WAY RAFTER ANGLE KIT
Each kit contains 12 angles.



Walltent shop

Canvas Tent Shop Angle Kit Sleeve

WILDERNESS GALVANIZED STEEL KITS - WITH SUPPORT BRACES FOR EXTRA STRENGH.

Purchasing angle kits and then purchasing 1" inside diameter, thin walled, electrical conduit at a local hardware store - is the most economical approach to purchasing an internal frame. Internal wall tent frame shipping charges are very high in Canada due to the weight of an internal frame.

TOP ALUMINUM RAIL FENCE TUBING WILL NOT WORK ON ANGLE KITS.

INSIDE DIAMETER OF ANGLE IS 1 3/16".

We will provide assistance if you have trouble understanding angle kit instructions.

Typical frame savings using an angle kit on a 12x14 internal frame is $200 and a 16x20 is $300.

95% of Canada Wall Tent Shop customers buy an angle kit and make their own frame.

Hunter custom angles are made to fit any tent. These custom angles will ship 1 - 4 weeks after ordering. Specify tent width and slope (roof) .

View How To Measure your existing Montana tent for a frame or wall tent angle kit.

View Angle Kit page for angle kit instructions to make your own tent frame from conduit.

The table below gives recommended rafter requirements for different lengths of tents.

If you expect heavy snow loads, add one additional rafter to your joint angle kit purchase. The additional rafter significantly increases the strength of your internal frame.

ORDERING ANGLE KITS: To insure you order/receive the correct degree of angle, have some one help you pull the tent taut to insure the tent is measured accurately. Measure your tent width ( C measurement ) and slope ( B measurement ). The slope is the distance from top of the ridge to where roof meets the wall. In comments of check out form, type in width and slope measurements.

THERE ARE NO RETURNS ON CUSTOM ANGLE KITS. NO EXCEPTIONS. Measure your tent accurately to insure you receive the correct degree of angles for your tent. If the tent measurements you provide are not accurate - the custom angle kit will not fit your tent. Therefore, you will have to order and pay for another set of custom angles.

ANGLE KITS - STEEL

KITS MAX TENT LENGTH

WILDERNESs


120 degrees

MONTANA

ANGLE KIT

CUSTOM

ANGLE KIT
3 Rafters - 9 Angles/12lbs 12' $160 $170 $190
4 Rafters - 12 Angles/12lbs 18' $210 $220 $240
5 Rafters - 16 Angles/20lbs 24' $260 $270 $290
6 Rafters - 18Angles/20lbs 30' $310 $320 $340

Porch Kit
2 Rafters

6 each 3 way Angles/8lbs

6' $120 $130 $140

Porch Kit
3 Rafters

6 each 3 way angles & 3 each 4 way angles/10lbs

12' $160 $170 $190
Angle Only 3 Way $20 $22 $25
Angle Only 4 Way $20 $22 $25
SLEEVES - 10" 6 sleeves $30 8 sleeves $40 10 sleeves $50 12 sleeves $60
T angle for bottom ground frame rail       $20
L angle for bottom ground frame rail       $20



Click to view tent frame Angle Kit Instructions that explains how to make your tent frame.

BEFORE ORDERING ---- I NEED YOUR B TENT (WIDTH) & C (SLOPE) TENT MEASUREMENT TO INSURE YOUR ANGLES FIT YOUR SPECIFIC TENT. PROVIDE B & C TENT MEASUREMENTS WHEN ORDERING.

IF YOU WANT TO MAKE A BOTTOM GROUND RAIL ON YOUR TENT FRAME, you will need a T angle for all middle legs and a L angle for the end legs. Cost is $20 per T angle and L angle. Call if you have questions.





EXTENDED FLY OR AWNING: TO MAKE AN ANGLE KIT FRAME EXTENSION FOR A TENT WITHOUT EAVE OPENINGS - I recommend a 4 way angle on the ridge end that goes through the canvas tent ridge end opening and purchase 3 more 3 way angles. Your ridge extension conduit will fit into the 4 way on the tent ridge end and then connect to a 3 way at the end of ridge extension/awning. Add end rafters and legs using the 2 remaining 3 way angles. I recommend you drill holes in the ridge extension angles and conduit and install nuts and bolts to keep these angles in place as there is no tent enveloping the frame to keep the frame in place during windy conditions. ( If ridge extension is more than 6' you will need to buy 3 each 4 way to add another set of rafters)


top
  Home | Canvas Tents | Tent Frame Angle Kits | Wall Tent Stoves | Canvas Tent Frames
Tent & Stove Info Guide | Angle Kit Instructions | Packing Tips | Pack Saddle & Panniers Info Guide

Canvas Tent Shop Canada

support@canvastentshop.ca